Linux version 2.6.16.5 (laforge@hanuman.de.gnumonks.org) (gcc version 3.3.2) #57 Mon Apr 17 11:24:38 CEST 2006
CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE)
Machine: Motorola Ezx Platform
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
Run Mode clock: 195.00MHz (*15)
Turbo Mode clock: 292.50MHz (*1.5, active)
Memory clock: 195.00MHz (/2)
System bus clock: 195.00MHz 
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists
Kernel command line: root=/dev/mtd2 rootfstype=cramfs ip=off console=ttyS2,115200n8 console=tty0
PID hash table entries: 128 (order: 7, 2048 bytes)
Console: colour dummy device 30x80
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 16MB = 16MB total
Memory: 14216KB available (1640K code, 235K data, 92K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing Cryptographic API
io scheduler noop registered (default)
pxa2xx-fb pxa2xx-fb: machine LCCR0 setting contains illegal bits: 00200878
pxa2xx-fb pxa2xx-fb: machine LCCR3 setting contains illegal bits: 00300008
Console: switching to colour frame buffer device 60x53
SA1100 Real Time Clock driver v1.02
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
$Id: ftl.c,v 1.59 2005/11/29 14:48:31 gleixner Exp $
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
INFTL: inftlcore.c $Revision: 1.19 $, inftlmount.c $Revision: 1.18 $
Probing PXA27x flash at physical address 0x00000000 (16-bit bankwidth)
PXA27x flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
 Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
RedBoot partition parsing not available
cmdlinepart partition parsing not available
Using static partition definition
Creating 6 MTD partitions on "PXA27x flash":
0x00000000-0x00020000 : "Bootloader"
mtd: Giving out device 0 to Bootloader
ftl_cs: FTL header not found.
0x00020000-0x00100000 : "Kernel"
mtd: Giving out device 1 to Kernel
ftl_cs: FTL header not found.
0x00120000-0x01a00000 : "rootfs"
mtd: Giving out device 2 to rootfs
ftl_cs: FTL header not found.
0x01a00000-0x01f80000 : "VFM_Filesystem"
mtd: Giving out device 3 to VFM_Filesystem
ftl_cs: FTL header not found.
0x01fa0000-0x01fc0000 : "setup"
mtd: Giving out device 4 to setup
ftl_cs: FTL header not found.
0x01fc0000-0x01fe0000 : "Logo"
mtd: Giving out device 5 to Logo
ftl_cs: FTL header not found.
No recognised DiskOnChip devices found
No valid DiskOnChip devices found
usbmon: debugfs is not available
pxa27x-ohci pxa27x-ohci: PXA27x OHCI
pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1
pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usb 1-3: new full speed USB device using pxa27x-ohci and address 2
usb 1-3: configuration #1 chosen from 1 choice
usbcore: registered new driver libusual
pxa27x_udc: version 21-Jul-2005
USB cmd disconnect
udc_probe:  successfully finished probe()
udc: udc_probe: test
udc: dev=0xc01ceaf0, driver=0xc01cf79c, speed=2,bind=0xc011c874, unbind=0xc011cb9c, disconnect=0xc011d1b4, setup=0xc011cc18
udc: pxa27x_config_ep is called
udc:  usb endpoint descriptor is:
        bLength:7
        bDescriptorType:5
        bEndpointAddress:80
        bmAttributes:2
        wMaxPacketSize:0
udc: UDCCR: 0xf2600404 is 0x200d103
udc: pxa27x_config_ep is called
udc:  usb endpoint descriptor is:
        bLength:7
        bDescriptorType:5
        bEndpointAddress:0
        bmAttributes:2
        wMaxPacketSize:0
udc: UDCCR: 0xf2600408 is 0x2014103
gs_bind: Gadget Serial v2.0 bound
udc: registered gadget driver 'g_serial'
USB cmd connect
udc: EP0_IDLE, udcicr B8000000.03, udcsir 00.00, udcfnr 1B0
udc: udccr 0x00000001 = ude, con=0,inter=0,altinter=0
udc: ep0 driver 'g_serial'
udc: udccsr0 EP0_IDLE 0x00000000 =
udc: ep0 IN 0/0, OUT 0/0
udc: udccs1 = 00
udc: udccs2 = 00
gs_module_init: Gadget Serial v2.0 loaded
i2c /dev entries driver
 : Enabling slave mode
 : i2c_pxa_set_slave: wait timedout
I2C: i2c-0: PXA I2C adapter, slave address 1
ezx_mci_init entered
pxamci_set_ios: clock 0 power 0 vdd 0.00
pxamci_set_ios: clkrt = 0 cmdat = 0
NET: Registered protocol family 2
pxamci_set_ios: clock 0 power 1 vdd 0.15
ezx_mci_setpower entered
pxamci_set_ios: clkrt = 0 cmdat = 0
pxamci_set_ios: clock 304688 power 2 vdd 0.15
ezx_mci_setpower entered
pxamci_set_ios: clkrt = 6 cmdat = 40
pxamci_set_ios: clock 304688 power 2 vdd 0.15
pxamci_set_ios: clkrt = 6 cmdat = 40
MMC: starting cmd 00 arg 00000000 flags 00000040
PXAMCI: irq 00000004
PXAMCI: stat 00002140
v=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
PXAMCI: request done
MMC: req done (0000): 0: 00000000 00000000 00000000 00000000
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
TCP bic registered
pxamci_set_ios: clock 304688 power 2 vdd 0.15
pxamci_set_ios: clkrt = 6 cmdat = 0
trying SD
MMC: starting cmd 37 arg 00000000 flags 00000015
PXAMCI: irq 00000004
PXAMCI: stat 00002140
v=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
PXAMCI: request done
MMC: req done (0037): 0: 00000000 00000000 00000000 00000000
send_app_op_cond, err: 4
trying MMC
MMC: starting cmd 01 arg 00000000 flags 00000061
PXAMCI: irq 00000204
PXAMCI: stat 00002142
v=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
w1=0x0000
w2=0x0000
PXAMCI: request done
MMC: req done (0001): 1: 00000000 00000000 00000000 00000000
pxamci_set_ios: clock 0 power 0 vdd 0.00
ezx_mci_setpower entered
pxamci_set_ios: clkrt = 6 cmdat = 0
VFS: Cannot open root device "mtd2" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
 <3>apm: an event queue overflowed